Designed with your next-generation studio demands in mind, Oasis allows you to cost-effectively and easily migrate from analog to digital whenever you’re ready. In addition to capabilities for all necessary audio and logic components, Oasis provides both analog and digital outputs that enable you to connect your facility with modern STLs and studio infrastructures.
An affordable solution for studios of any size and budget, Oasis is built with the combination of cost-efficient engineering and high quality you expect from PR&E products.
Options and Installation
The Oasis audio console is available in two sizes:
8-fader channels and 12-fader channels.
Oasis has two basic input options — a balanced analog A/B input card and a microphone line A/B input card. Each hot-swappable card represents eight total inputs available to the four corresponding faders.
Each Oasis frame size has a standard analog input configuration. This configuration provides 4 channels of Mic-pre/Line Inputs. The remaining inputs are analog Line/Line cards each supporting 4 additional faders.
The console provides all the monitoring outputs needed, including monitor and headphones for control room and studio. It even offers a remote level control option for the studio monitors, along with a direct “talk to studio” interface from the console.
Oasis features two meters, the second of which is switchable. It also displays an event timer with the controls necessary to track all show elements.
In addition to the host of standard Oasis features, an optional 8x1 RLS module is also available as an option for input expansion. The control for this remote line selector is offered in a convenient console drop-in panel.
Phoenix Conbicon connectors allow for rapid and easy wiring without the need for any special crimpers or tools.
Analog Line Inputs (all inputs and outputs are +4 dBu, balanced):
Input Impedance : >40 k ohms, balanced
Nominal Input Level : +4 dBu
Maximum Input Level : +24 dBu
Analog Line Outputs (all inputs and outputs are +4 dBu, balanced):
Output Source Impedance : <3 ohms="" balanced="" span="">
Output Load Impedance: 1 k ohms minimum
Nominal Output Level : +4 dBu
Maximum Output Level : +24 dBu
Conversions: A/D 24--bit, Delta--Sigma, 128x oversampling
D/A 24--bit, Delta--Sigma, 128x oversampling Latency: <1.6 ms="" analog="" input="" to="" output="" span="">
AES--3 Output Compliance: 24--bit
Output Sample Rate: 44.1 kHz, system referenced
Processing Resolution: 24--bit
Logic Inputs: Opto--isolated, floating or referenced to internal +5 VDC via DIP switch
Logic Outputs: Opto--isolated, floating or referenced to internal ground via DIP switch.
Outputs are independently configured for pulse or continuous, open or closed operation
Audio Frequency Response:
Analog Input to Analog Output: +0.3 dB/-0.0 dBr, 20 Hz to 20 kHz
Audio Dynamic Range (referenced to FSD):
Analog Input to Analog Output: 103 dB, 106 dB “A” weighted
Analog Input to Digital Output: 107 dB
Audio Total Harmonic Distortion + Noise:
Analog Input to Analog Output: <0.005%, 20 Hz to 20 kHz, +18 dBu input, +18 dBu output
Audio Crosstalk Isolation:
Adjacent Analog Inputs or Outputs: >95 dB, 20 Hz to 20kHz
Dimensions (H xW xD): Oasis-08: 5.49 x 22.0 x 17.25 in.; Oasis-12: 5.49 x 28.4 x 17.25 in.
Type: External, ‘line lump’ style, plug-in power supply
Input voltage: 100 to 240 VAC, 50/60 Hz
AC input: Detachable IEC cord with C5 connector
Output voltage: +12 VDC
Power Requirements: <100 w="" at="" 120="" vac="" 60="" hz="" span="">
FSD = Full Scale Digital, +24 dBu; Analog outputs measured with >1 k ohm load; Total Harmonic Distortion (THD+N) is measured at +18 dBu, using a 1 kHz or a swept signal with a 22 kHz low pass filter
0 dBu corresponds to 0.775 volts RMS — regardless of the circuit impedance, which is equal to 0 dBm, as measured on a 600 ohm circuit: